| Inspection Type |
Planned
|
| Scope |
Partial
|
| Safety/Health |
Safety
|
| Close Conference |
2017-03-06
|
| Emphasis |
L: FALL, P: FALL
|
| Case Closed |
2022-08-11
|
Violation Items
| Citation ID |
01001 |
| Citaton Type |
Serious |
| Standard Cited |
19260304 D |
| Issuance Date |
2017-05-12 |
| Abatement Due Date |
2017-05-24 |
| Current Penalty |
3259.0 |
| Initial Penalty |
3259.0 |
| Final Order |
2017-06-08 |
| Nr Instances |
1 |
| Nr Exposed |
2 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1926.304(d): Portable, power-driven circular saw(s) were not equipped with a guard above and below the base plate or shoe: (a) On or about 3/6/2017 - 2981 Grants Mill Road, Leeds, AL, a Makita, Model 5007F, Serial #1647413Y, circular saw being used to cut/trim sheathing for installing on the roof had the bottom guard shimmed to prevent it from closing. |
|
| Citation ID |
01002 |
| Citaton Type |
Serious |
| Standard Cited |
19260501 B11 |
| Issuance Date |
2017-05-12 |
| Current Penalty |
2770.0 |
| Initial Penalty |
2770.0 |
| Final Order |
2017-06-08 |
| Nr Instances |
1 |
| Nr Exposed |
3 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1926.501(b)(11): Each employee on a steep roof with unprotected sides and edges 6 feet (1.8 m) or more above lower levels was not protected from falling by guardrail systems with toeboards, safety net systems, or personal fall arrest systems: (a) On or about 3/6/2017 - 2981 Grants Mill Road, Leeds, AL, employees attaching felt to roof sheathing were not protected from falling approximately 11 feet. |
|
| Citation ID |
01003 |
| Citaton Type |
Serious |
| Standard Cited |
19261053 B01 |
| Issuance Date |
2017-05-12 |
| Current Penalty |
2173.0 |
| Initial Penalty |
2173.0 |
| Final Order |
2017-06-08 |
| Nr Instances |
1 |
| Nr Exposed |
4 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1926.1053(b)(1): Where portable ladders were used for access to an upper landing surface and the ladder's length allows, the ladder side rails did not extend at least 3 feet (.9 m) above the upper landing surface being accessed: (a) On or about 3/6/2017 - 2981 Grants Mill Road, Leeds, AL, the ladder used by employees to access the roof was extended approximately 8 inches above the landing. |
|
| Citation ID |
02001A |
| Citaton Type |
Other |
| Standard Cited |
19260405 G02 IV |
| Issuance Date |
2017-05-12 |
| Abatement Due Date |
2017-05-24 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2017-06-08 |
| Nr Instances |
1 |
| Nr Exposed |
2 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1926.405(g)(2)(iv): Flexible cords were not connected to devices and fittings so that strain relief is provided to prevent pull from being directly transmitted to joints or terminal screws: (a) On or about 3/6/2017 - 2981 Grants Mill Road, Leeds, AL, an extension cord where strain relief was pulled away and the outer sheath damaged was being used to power a Ryobi, Model CSB134L, 7 1/4 inch circular saw. |
|
| Citation ID |
02001B |
| Citaton Type |
Other |
| Standard Cited |
19260416 E01 |
| Issuance Date |
2017-05-12 |
| Abatement Due Date |
2017-05-24 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2017-06-08 |
| Nr Instances |
1 |
| Nr Exposed |
2 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1926.416(e)(1): Worn or frayed electric cords or cables were used: (a) On or about 3/6/2017 - 2981 Grants Mill Road, Leeds, AL, an extension cord with outer sheath damage was used to power a Ryobi, Model CSB134L, 7 1/4 inch circular saw. |
|
| Citation ID |
03001 |
| Citaton Type |
Other |
| Standard Cited |
19030019 C01 |
| Issuance Date |
2017-06-30 |
| Abatement Due Date |
2017-08-07 |
| Current Penalty |
305.0 |
| Initial Penalty |
305.0 |
| Final Order |
2017-07-27 |
| Nr Instances |
3 |
| Nr Exposed |
2 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1903.19(c)(1): The employer did not certify to OSHA, within 10 calendar days after the abatement date, that the cited violation had been abated: (a) On or about 06/05/2017, the employer failed to submit certification of corrective action for citation 1, item 1 issued on 05/12/2017 with an abatement date of 05/24/2017. (b) On or about 06/05/2017, the employer failed to submit certification of corrective action for citation 2, item 1a issued on 05/12/2017 with an abatement date of 05/24/2017. (c) On or about 06/05/2017, the employer failed to submit certification of corrective action for citation 2, item 1b issued on 05/12/2017 with an abatement date of 05/24/2017. |
|
|
